ASTM F2639-07e1

Click here to purchase

1.1 DefinitionThis practice defines acceptable practices and processes for the design, alteration, and certification of electric systems and installations in general aviation aircraft. This practice does not change or create any additional regulatory requirements nor does it authorize changes in or permit deviations from existing regulatory requirements.

1.2 ApplicabilityThe guidance provided in this practice is directed to air carriers, air operators, design approval holders, Supplemental Type Certificate (STC) holders, maintenance providers, repair stations, and anyone performing field approval modifications or repairs.

1.3 Protections and CautionsThis practice provides guidance for developing actions and cautionary statements to be added to maintenance instructions for the protection of wire and wire configurations. Maintenance personnel will use these enhanced procedures to minimize contamination and accidental damage to electrical wiring interconnection system (EWIS) while working on aircraft.

1.4 Protect and Clean As You Go PhilosophyThis philosophy is applied to aircraft wiring through inclusion in operators' maintenance and training programs. This philosophy stresses the importance of protective measures when working on or around wire bundles and connectors. It stresses how important it is to protect EWIS during structural repairs, STC installations, or other alterations by making sure that metal shavings, debris, and contamination resulting from such work are removed.

1.5 This practice includes the following sections:

Title Section
Wire Selection 5
General 5.1
Aircraft Wire Materials 5.2
Table of Acceptable Wires 5.3
Severe Wind and Moisture Problems (SWAMP) 5.4
Grounding and Bonding 5.5
Electrical Wire Chart 5.6
Wire and Cable Identification 6
General 6.1
Wire and Cable Identification 6.2
Types of Markings 6.3
Sleeve and Cable Marker Selection 6.4
Placement of Identification Markings 6.5
Wiring Installation 7
General 7.1
Wire Harness Installation 7.2
Power Feeders 7.3
Service Loops 7.4
Drip Loops 7.5
Soldering 7.6
Strain Relief 7.7
Grounding and Bonding 7.8
Splicing 7.9
Fuel Tank Wiring 7.10
Corrosion Preventative Compounds (CPC)
(MIL-C-81309)
7.11
Electrical Load Considerations 8
General 8.1
Methods for Determining the Current-Carrying
Capacity of Wires
8.2
Acceptable Means of Monitoring and
Controlling the Electrical Load
8.3
Electrical System Components 9
General 9.1
Alternators 9.2
Generators 9.3
Ground Power Units 9.4
Auxiliary Power Units 9.5
Batteries 9.6
Circuit Protection Devices 9.7
Conduit 9.8
Connectors 9.9
Inverters and Power Converters 9.10
Junctions 9.11
Junction Boxes 9.12
Electronic Assemblies 9.13
Relays 9.14
Studs 9.15
Switches 9.16
Terminals and Terminal Blocks 9.17
Waveguides 9.18
Electrical System Component Installation 10
General 10.1
Alternators 10.2
Generators 10.3
Auxiliary Power Units (APUs) 10.4
Batteries 10.5
Circuit Protection Devices 10.6
Conduit 10.7
Connectors 10.8
Inverters and Power Converters 10.9
Junctions 10.10
Junction Boxes, Panels, Shields, and
Microswitch Housings
10.11
PC Board Assemblies 10.12
Relays 10.13
Studs 10.14
Switches 10.15
Terminals and Terminal Blocks 10.16
Waveguides 10.17
EMI/RFI 11
General 11.1
Grounding and Bonding 11.2
HIRF 11.3
Lightning 11.4
Alterations 12
General 12.1
Wire Substitutions 12.2
Commercial Off-the-Shelf (COTS) Components 12.3
Electrical Load Considerations 12.4
Batteries 12.5
Circuit Breakers 12.6
Junction Boxes 12.7
Relays 12.8
Switches 12.9
Wire Marking 12.10
Wire Bundle Routing 12.11
Wire Bundle Combing 12.12
Interference Tests 12.13
System Safety Assessments 12.14
Certification Processes 13
General 13.1
Certification 13.2
Alterations and Maintenance 13.3

1.6 ValuesThe values given in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. See Appendix X2 for SI-based prefixes and powers of 10.

Note 1 – Where SI units are required, refer to Annex 5 of ICAO.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Product Details

Published:
09/01/2007
Number of Pages:
101
File Size:
1 file , 4.4 MB